The Newcomb 36 gas fireplace is a contemporary styled fireplace that offers a great first impression for any room. The fireplace is available in Standard or Deluxe systems, each with different features. The Standard system includes basic remote control, while the Deluxe system includes a 7 day programmable thermostat remote, 6 stage dual fan control, and modulating valve for flame control. The fireplace also offers two optional surrounds options, stainless steel and decorative black, and comes standard with contemporary black porcelain panels, black reflective glass, and a 3 piece rock set. It runs on natural gas but it is also available for liquid propane use. Included Accesories: Features: -Clean face design-Tempered glass-100% safety shutoff-Top vent only-Electronic ignition-Black porcelain panels-Black glass and 3 piece rock set-Basic remote control Specifications: FRAMING DIMENSIONS VIEWING AREA BTUS (NG) AFUE / P.4(NG EFFICIENCY) WEIGHT* HI LOW 33-1/2” H x 38” W x 15-1/2” D 15” H x 32-1/2” W 21,000 13,000 65.1 % 115 lbs. VENTING** CEILING /MANTLE HEIGHT 4” flex vent on exhaust side7” flex vent on the air intake side Internal ceiling = minimum 48”Mantle Height = minimum 40” **Venting – Any certified 2 ply flex piping can be used. Certified on Duravent, Selkirk, Metal Fab, ICC Warranty: Your Sierra Flame gas fireplace is guaranteed to be free of defects in materials and workmanship for a period of 5 years from the date of purchase. This covers: combustion chambers, heat exchangers and burners as well as stainless steel parts against tarnishing. Electrical (110 volt and millivolt) components and wearable parts such as blowers, gas valves, thermal switches, switches, wiring, remote controls, igniters, gaskets, glass (thermal damage only) and pilot assemblies are covered for 1 year and Sierra Flame will provide replacement parts free of charge during the first year of the limited warranty CONDITIONS AND LIMITATIONS Sierra Flame warrants its products against manufacturing defects to the original purchaser only – ie. the individual or legal entity (registered customer) whose name appears on the original invoice – provided that the purchase was made through an authorized Sierra Flame dealer and is subject to the following conditions and limitations: This factory warranty is nontransferable and may not be extended whatsoever by any of our representatives. A licensed, authorized service technician or contractor must have installed the gas fireplace. Installation must be done in accordance with the installation instructions included with the product and all local and national building and fire codes. This limited warranty does not cover damages caused by misuse, lack of maintenance, accident, alterations, abuse or neglect. Parts installed from other manufacturers will nullify this warranty. This limited warranty further does not cover any scratches, dents, corrosion or discoloring caused by excessive heat, abrasives, chemical cleaners nor any venting components used in the installation of the fireplace. This warranty does not cover any problems caused to installation used venting or vent terminations which are not certified for use with this product. Any installation, labor, construction, transportation or other related costs or expenses arising from defective part(s), repair or replacement or otherwise of same, will not be covered by this warranty nor shall Sierra Flame assume responsibility for same. Further, Sierra Flame will not be responsible for any incidental, indirect or consequent damages, except as provided by law, and in no event shall they exceed the original purchase price. As part of industry warranty standards all faulty gas units/ parts, must be returned to our headquarters and fully inspected prior to any warranty credits being issued. Please provide carrier tracking information on when the parts were returned to our office. Only parts deemed manufacture defective will be credited. In the first year only, this warranty extends to the repair or replacement of warranted parts, which are defective in material or workmanship provided that the product has been operated in accordance with the operation instructions and under normal conditions. After the first year, Sierra Flame may, at its discretion, fully discharge all obligations with respect to this warranty by refunding to the original warranted purchaser the wholesale price of any warranted but defective parts. Notwithstanding any provisions contained in this warranty, Sierra Flame’s responsibility under this warranty is defined as above and it shall not in any event extend to any incidental, consequential or indirect damages. This warranty defines the obligations and liability of Sierra Flame with respect to the Sierra Flame gas fireplace and any other warranties expressed or implied with respect to this product, its components or accessories are excluded. Sierra Flame neither assumes, nor authorizes any third party to assume, on its behalf, any other liabilities with respect to the sale of this product. Sierra Flame will not be responsible for: over firing, downdrafts, spillage caused by environmental conditions such as rooftops, buildings, nearby trees, hills, mountains, inadequate vents, excessive venting configurations, insufficient make up air, or negative air pressures which may or may not be caused by mechanical systems such as exhaust fans, furnaces, clothes dryers, etc. Any damages to fireplace, combustion chamber, trim or other component due to water, weather damage, long periods of dampness, condensation, damaging chemicals or cleaners will not be the responsibility of Sierra Flame. The bill of sale or copy will be required together with a serial number and a model number when making any warranty claims from your authorized dealer. Sierra Flame reserves the right to have its representative inspect any product or part thereof prior to honoring any warranty claim. Return Policy: Please note that only goods accompanied by a return material authorization number can be processed. Returned goods which arrive at our premises without an authorized RMA number shall be refused or returned at the cost of the sender. The following procedure is to be followed to in order to ensure proper and undamaged returns processing. • All goods to be returned must be reported in advance. Please use the “Request to return product” form. This form is available in the dealer login area of sierraflame.com or by emailing your representative.•All goods which have been registered and approved for return are assigned a return material authorization number that is communicated in advance to our receiving warehouse. • We will email you a copy of the RMA label with unique number as well placement instructions.• This is to accompany the returned goods when you send it to us. One copy should be retained for your records. The returned material authorization (RMA) number must be included in any correspondence regarding the shipment. You will be given the shipping address upon approval. IMPORTANT: Please observe all of the following provisions Products can only be accepted for return upon receipt of our written approval. Returns should, of course, be limited to those brought about in exceptional circumstances. As a rule, the following cannot be returned • Products which are eligible for parts under our warranty• Products damaged in transit (please refer to ordering policy regarding freight claims) • Products that have had their original manufacturers packaging opened• Products that have been out of their original manufacturers packaging Products which have been ordered incorrectly may be returned within 7 days of delivery, as long as they are still in the original packaging and have not been used or installed, are re-saleable and in a technically faultless condition. The packaging must be in its original state, i.e. unopened and the exterior must not be altered by the presence of any permanent marker, branding or labels that will damage the carton. Goods delivered to our premises shall only be accepted if freight has been prepaid by the shipper. Products must be returned via freight carrier and properly secured on a appropriately sized pallet. To minimize exposure to the packaging, it is advised that the unit be wrapped in plastic wrap once secured to the pallet. Units must not be shipped via courier and any units arriving to the warehouse via courier (such as but not limited to UPS or FEDEX) will not be accepted and will be returned to the sender at the expense of the customer. Returns must include a copy of the original invoice as well as a copy of the RMA label provided. If the packaging showssigns of damage,the product will be returned at the expense of the customer or scrapped,as desired. If a return is desired, we are to be notified of this within a period of 5 days. All returns are subject to a 20% restocking fee.
Checkout happens on the official store. This page mirrors catalog facts in plain HTML for direct reading and crawlability.