MAHLE EV-1 Portable Exhaust Ventilator System An exhaust check means running an engine indoors on purpose. The EV-1 exists so that the fumes leave the building instead of the technician. It is a portable, wheeled ventilator — a 0.75 HP motor moving 270 CFM (460 CMH) down a 40 ft hose — that you position at the vehicle and route out through a door or a vent, then wheel out of the way when the job is done. The number that separates it from a shop fan and a length of ducting is the one most equipment of this type never publishes: an A-weighted surface noise rating of 73 dB(A). Ventilation only protects people if it is actually switched on, and a blower that makes conversation impossible in the bay is a blower that gets left in the corner. A published, corrected sound figure is something you can hold against your own noise policy rather than something you find out about after delivery. Will It Fit Your Shop? The unit occupies 40 in x 22 in x 22 in (102 cm x 56 cm x 56 cm) and weighs 73 lb (33 kg) — a two-hand push, not a forklift job, and it stores in the space a wheeled toolbox would take. The specification that decides whether it works in your building is the hose: 40 ft (12 m) long and 5 in (12.7 cm) in diameter. Measure the real route, not the straight line — from where a vehicle's tailpipe sits in the bay you actually use, around the obstacles, to the opening the fumes will leave by. Forty feet is generous for a single bay and tight if the only outside door is at the far end of a three-bay shop. Diameter matters too: a 5 in hose wants a 5 in path, so if you are planning to pass it through a wall port or a cracked door, check the opening. Power is straightforward. The motor runs on 110 VAC and the manufacturer specifies a minimum 6 Amp supply, so a standard shop circuit will do — but it should be a circuit with headroom, not the one already carrying a compressor. Working temperature is rated 23° to 120°F (-5° to 49°C), which is worth checking against an unheated winter bay. Confirming the power supply, the hose route and the exit point is the buyer's responsibility; these are measurements only someone standing in the building can take, and we would rather answer the question before the order than after. Why Airflow Volume Is the Specification That Counts Ventilation is a volume problem, not a pressure problem. What protects a technician is how much air actually moves per minute, which is why the EV-1 is specified at 270 CFM through the full hose rather than by motor size alone. A 0.75 HP motor driving that airflow is a sensible pairing: enough to sustain the flow along 40 ft of 5 in hose, small enough to run on an ordinary circuit and to stay within that 73 dB(A) rating. The manufacturer describes the design as high-flow positive pressure ventilation. In practice the value of a portable system is that it goes where the work is: an exhaust check on the third car of the morning does not have to happen in the one bay with a fixed extraction drop, and a shop that grows or rearranges its bays does not have to re-engineer ducting to keep up. Serviceable, Not Sealed The unit is protected by two 16 Amp time-delayed fuses measuring 0.39 in x 1.49 in (10 mm x 38 mm) — an ordinary industrial cartridge size, not a proprietary part. Time-delayed is the right choice here: a blower motor draws a surge at start-up, and a fast fuse would nuisance-blow every morning. Keep a pair on the shelf; that is the failure a shop can fix in a minute rather than a service call. Perfect For Independent repair shops doing emissions and exhaust checks in bays with no fixed extraction. Inspection and testing stations that run engines indoors as a routine part of the work. Fleet and municipal garages needing one system that can be shared across several bays. Rented or leased premises where installing permanent ducting is not an option — this rolls in and rolls out with you. Serious home and club workshops where running an engine in an attached garage is the exact thing you should not do unventilated. What's in the Box The ventilator with its 110V 0.75 HP motor and the 40 ft x 5 in hose. The manufacturer's own summary of the unit is short and worth repeating in full: highly portable and practical in design, simple in operation, with a 110V 0.75 HP motor for high-flow positive pressure ventilation. We have not listed clamps, adapters or tailpipe fittings here because the data we hold does not itemise them — if a specific tailpipe connection matters to your workflow, ask us before ordering rather than assuming it is in the crate. Specifications Model EV-1 Flow capacity 270 CFM (460 CMH) Noise rating Corrected LpA = 73 dB(A) Motor 110 VAC, 0.75 HP Power source Minimum 6 Amp Fuses Two, 16 Amp time delayed, 0.39 in x 1.49 in Hose 40 ft long, 5 in diameter Working temperature 23° to 120°F Dimensions 40 in x 22 in x 22 in Weight 73 lb (33 kg) Certification, Honestly Ventilation equipment is one category where buyers do ask about listings and approvals, so we will be plain: the product data we hold for the EV-1 records no third-party listing and no conformity marking, and we are not going to imply one. The manufacturer does publish a corrected sound rating, which is a measured figure rather than a marketing claim, and that is on the page above. If your insurer, an employer's safety programme, a corporate purchasing standard or a local requirement asks for equipment carrying a specific approval, contact us before you order and we will go back to the manufacturer for the documentation rather than let you assume. Shipping and Delivery This system ships by freight within the lower 48 states. This item ships free, so there is nothing to add at checkout. You must be able to receive and unload the shipment, or arrange to collect it from the carrier's terminal — the driver is not obliged to bring it inside or to help. Residential delivery is available and carries a residential fee. Inspect the shipment before you sign for it and note any damage or shortage on the delivery receipt at the time of delivery. A receipt signed clean is very hard to argue with afterwards, and a hose is easy to crush in transit. Warranty This unit is covered by the manufacturer's warranty; the current terms are on our warranty claims page. We have deliberately not printed a period here, because the data we hold for this model does not state one — message or call us and we will confirm the exact term before you buy. If a fault appears, contact us first and leave the unit intact: dismantling equipment or attempting a repair before a claim has been opened is the most common reason a valid claim is refused. Product Features Highly portable, practical design Simple operation 110V ¾ HP motor for high-flow positive pressure ventilation Product Specifications Model EV-1 A-Weighted Surface Noise Rating Corrected LpA = 73 dB (A) Flow Capacity 270 CFM (460 CMH) Fuses Qty (2); 16 Amp time delayed 0.39 in x 1.49 in (10 mm x 38 mm) Hose 40 ft (12 m) long; 5 in (12.7 cm) diameter Motor 110 VAC (0.75 HP) Power Source Minimum 6 Amp Working Temperature 23° to 120°F (-5° to 49°C) Dimensions 40 in x 22 in x 22 in (102 cm x 56 cm x 56 cm) Weight 73 lb (33kg) Pick Up and Delivery Call, text, or chat with us if you have questions. 866-774-7743
Checkout happens on the official store. This page mirrors catalog facts in plain HTML for direct reading and crawlability.