BendPak 10APX: arms that retract to 22 in. and reach out to 57 in. Two-post lifts are compared on capacity, and capacity is rarely the thing that stops you using one. What stops you is an arm that will not go short enough to tuck under a low sill, or long enough to reach a pick-up point set well inboard on a pickup truck. The 10APX publishes both ends of that range: front arms from 22 in. / 559 mm to 47.5 in. / 1,207 mm, rear arms from 29.5 in. / 749 mm to 57 in. / 1,448 mm, measured at the pad. The three-stage telescoping construction is what buys the spread — a triple-telescoping arm collapses shorter and extends further than a two-stage arm occupying the same space. Combined with drop-end Low-Pro arms and a minimum pad height of 4 in. / 102 mm, it is a 10,000 lbs / 4,536 kg lift that can genuinely take a lowered car and a work van in the same day. Will It Fit? The overhead beam sits at 157 in. / 3,988 mm, so this needs a tall bay — measure to the lowest obstruction, not to the ceiling, because lights, ducting and door tracks are what people forget. The lift installs in two footprints: overall width 135 in. / 3,429 mm or 145 in. / 3,683 mm, with 108.25 in. / 2,750 mm or 118.25 in. / 3,004 mm between the columns and drive-through clearance of 92 in. / 2,337 mm or 102 in. / 2,591 mm. That choice is made at installation and is the one thing you cannot revise afterwards. Power is 220 VAC, 60 Hz, 1 Phase, and the unit is quoted at under 70 dB. Our record does not state the concrete thickness or compressive strength required. On a two-post lift the whole load reaches the floor through the anchors, so do not assume it — the figure is in the installation manual linked on this page and we will confirm it in writing on request. Ceiling, slab and circuit are the buyer's responsibility to verify before ordering. Rise, and what a screw pad adds to it Rise at the carriage is 75 in. / 1,905 mm. With the screw pad wound up it becomes 79.5 in. / 2,007 mm, and with a 63 mm adapter fitted on top of that, 89 in. / 2,261 mm. Those are three different answers to "how high does it go", and all three are correct — they just measure to different places. The number that matters to you is the one measured to whatever will actually be touching the vehicle. The pads are double-telescoping and spin up by hand, which is how you level a vehicle whose pick-up points are not all at the same height. BendPak also offers stackable adapters in 2.5 in. and 5 in. heights, and frame cradle pads with 35 mm or 60 mm pins for trucks and SUVs with rectangular steel frames. Those are accessories, not inclusions. The restraint, and the number to compare it on An automatic swing arm restraint stops an arm moving when a vehicle shifts on the pads — which happens when a technician leans on a stubborn fastener, or when pulling a gearbox moves the balance. This one is forged steel, grips through a full 360 degrees, and is rated to hold against over 2000 pounds of side force. It sets itself as the lift rises, so there is no procedure to skip. The other figure worth having is the per-arm rating: 2,500 lbs / 1,134 kg, against axle limits of 5,000 lbs / 2,268 kg. A load distributed badly can reach an arm limit while the total is still well under 10,000 lbs. Perfect For Professional bays handling a mixed intake, from lowered cars to light commercials, on one set of arms. Shops servicing electric vehicles, whose lift points sit outboard and whose kerb weights punish under-specified arms. Serious home workshops with the ceiling height for a full-rise two-post lift. Tire and brake work where the asymmetric arm position keeps the doors clear. What's in the Box Two columns with the expandable top beam and oversized 53 in. and 59 in. carriages; four triple-telescoping Bi-Metric arms with double-telescoping screw pads and drop ends; the automatic arm restraints; safety locks spaced every 3 in. in each column with single-point release; the padded overhead safety shutoff bar; 3/8 in. (10 mm) high-strength multi-strand galvanised steel equalising cable over oversized sheaves; and the electric-hydraulic HVLP power unit, all in a powder coat finish. Frame cradle pads, stacking adapters and the WSA-100 air and electric work station — four 110V outlets with 20 amp industrial GFI protection, plus two air outlets — are separate accessories. Specifications Specification Figure Lifting capacity 10,000 lbs / 4,536 kg Capacity per axle 5,000 lbs / 2,268 kg front and rear Maximum load per lift arm 2,500 lbs / 1,134 kg Rise 75 in. / 1,905 mm Rise plus pad 79.5 in. / 2,007 mm Rise plus pad plus 63 mm adapter 89 in. / 2,261 mm Minimum height with pad 4 in. / 102 mm Height overall 157 in. / 3,988 mm Width overall 135 in. / 3,429 mm or 145 in. / 3,683 mm Outside columns 127 in. / 3,226 mm or 137 in. / 3,480 mm Inside columns 108.25 in. / 2,750 mm or 118.25 in. / 3,004 mm, about 10 ft Drive-through clearance 92 in. / 2,337 mm or 102 in. / 2,591 mm, about 8.5 ft Front arm reach 22 in. / 559 mm to 47.5 in. / 1,207 mm Rear arm reach 29.5 in. / 749 mm to 57 in. / 1,448 mm Screw pad adjustment 2 in. / 51 mm Arm restraint 360 degrees, over 2000 pounds of side force Motor and noise 220 VAC, 60 Hz, 1 Phase; under 70 dB Time to full rise 45 seconds Certification This lift is listed as ALI certified in its own feature list. In practice that means an independent body has assessed the design against a recognised lift safety standard, rather than the manufacturer declaring conformity on its own authority — and it is that independent assessment which insurers, fleet policies and some local code officials ask for by name. A line in a feature list is a good sign; a certificate tied to a model and serial number is what satisfies an auditor. If you need documentary evidence for an inspection or an insurance file, ask us in writing and we will obtain it. Shipping and delivery This item ships free within the lower 48 states, so there is nothing to add at checkout. That is why no shipping figure is written into this page. The carrier delivers to the kerb. Arrange the unload beforehand — a forklift on site, or terminal collection, which is often easier for crated columns. A residential address carries a residential fee. Warehouse pickup can be arranged for this brand — call us to set it up. Inspect before you sign and note any damage on the bill of lading at the time. Warranty The warranty document governing this lift is linked on this page; read the term and its exclusions there rather than in a summary. Whatever it says, do not dismantle a component you intend to claim on. Photograph it in place, leave it assembled and contact us first. Product Features Durable powder coat finish Expandable top beam accommodates wide or narrow drive-thru configurations Double-telescoping screw pads offer increased versatility Padded overhead safety shutoff bar Exclusive Bi-Metric™ arm design for more versatile arm positioning Single-point safety release Drop-end arms provide a lower pad height Dual hydraulic direct-drive cylinders Oversized 53" & 59" tall carriages for superior strength and durability Electric / hydraulic HVLP power system Self-lubricating dura-glide UHMW polyethylene bearing system Safety locks in each column spaced every 3" Automatic arm restraints withstand over 2000-pounds of side force 3/8"(10mm) High-strength multi-strand galvanized steel equalizing cable Oversized cable sheave diameter reduces cable fatigue Four triple-telescoping arms ALI certified WSA-100 Easy to install Adapts to any two-post lift and four-post lift Electrical outlets equipped with 20 amp industrial GFI protection Electrical outlets located above the air service to prevent moisture damage and tangling Air service through 2 outlets: one lubricated for tire inflation and one for pneumatic tools Air service filter element and lubricator filler port are easily accessible Nickel-plated ball valve shutoff Powder-coated finish for durability and long life Four 110V GFI outlets Oiler Air supply Pressure gauge Storage hooks for hose and tools Regulator / filter Air inlet Frame Cradle Pads Set of 4 60mm pin Medium Adapter (60mm Pin) Set of 4 2.5” Tall Adapter (60mm Pin) Set of 4 5” Pick Up and Delivery Our Pick Up locations for Bendpak/Dannmar/Ranger are located in Santa Paula, California & Theodore, Alabama.Call, text, or chat with us if you have questions. 866-774-7743
Checkout happens on the official store. This page mirrors catalog facts in plain HTML for direct reading and crawlability.