The number that decides whether a high-roof van fits is 175.5 in., not 181 in. The BendPak 10APX-181 is the tall-beam member of the 10AP two-post family, built for shops that keep running out of headroom on cargo vans and high-cab trucks. Its structure stands 181 in. (4,597 mm) tall. But the figure that actually stops a vehicle is lower than that: this lift carries a padded overhead safety shutoff bar, and BendPak publishes the floor-to-overhead-switch distance as 175.5 in. (4,458 mm). The bar is what a van roof touches, and touching it cuts the lift. Measure your bay against 181 in.; measure your tallest vehicle against 175.5 in. Those are two different jobs and people conflate them all the time. Underneath that beam is a 10,000 lbs. (4,536 kg) two-post lift with an expandable top beam, triple-telescoping arms and forged-steel automatic arm restraints. Will It Fit? Take these to the bay with a tape measure before you order. On a two-post lift the room is the constraint far more often than the vehicle. Overhead. Overall height 181 in. (4,597 mm); floor to the shutoff bar 175.5 in. (4,458 mm). Allow room to stand the columns up during installation. Width. The top beam is expandable, so this model has two published widths: overall 135 in. (3,429 mm) or 145 in. (3,683 mm), outside the columns 127 in. (3,226 mm) or 137 in. (3,480 mm). Between the columns. 108.25 in. (2,750 mm) narrow, or 118.25 in. (3,004 mm) wide. Drive-through. 92 in. (2,337 mm) narrow, or 102 in. (2,591 mm) wide — the gap between the carriages, which on a van matters as much as the ceiling. Getting under a low car. Minimum height with the pad fitted is 4 in. (102 mm). Power. 220V single-phase, run to the location shown in the installation manual before the freight arrives. Ceiling height, bay width and the electrical supply are the buyer's responsibility to confirm; a lift that will not stand up in the room is not a warranty matter. Our record does not state a concrete thickness or strength requirement for this model. On a two-post lift every ounce of load goes into the anchors, so please do not assume the slab is adequate. The installation manual linked on this page carries the figure, and we will confirm it in writing before you order if you ask. Confirm the rise before you order Published figures for the rise on this model differ, so both are shown here, each beside the source that states it. Reading Where it comes from Value Rise (line A) BendPak's published specification sheet 75 in. (1,905 mm) Maximum rise under the arms A separate field in our catalogue record 71 in. If working height is the reason you are buying a high-rise lift, ask us to confirm the rise in writing before you order. We will get the answer straight from BendPak. Time to full rise is 45 seconds. Forged arm restraints, and why they exist Swing-arm restraints are not there for the moment the car goes up. They are there for the moment something changes while it is up. Pull a gearbox, lean on a stuck subframe bolt, and the centre of balance shifts suddenly across arms extended a long way from the columns. BendPak's forged-steel Automatic Swing Arm Restraint System holds each arm against more than 2000 pounds of load-holding force and engages on its own as the lift rises, with a quick-release lever when you want the arms to move. The safety locks follow the same principle: they engage automatically through the rise, spaced every 3 in. in each column, and a single-point release drops all of them together on the way down. Arms that retract as far as they extend Arm reach is usually quoted at the long end, which tells you half the story. A triple-telescoping arm matters for how short it goes as much as how far it stretches: the nested design lets the inner tube retract back through the arm assembly instead of stopping at an end plate. Front arms come in to 22 in. (559 mm) and out to 47.5 in. (1,207 mm); rears run 29.5 in. (749 mm) to 57 in. (1,448 mm). The Bi-Metric arms are the other half of it: the same four arms handle symmetric and asymmetric lifting without swapping anything, a 2-in-1 design that saves the swap when a low sports car follows a pickup onto the same lift. Low-Pro swing arms use a shorter channel profile and a dropped-end pad receiver, so there is less to catch a side skirt or running board on a lowered chassis. Each arm is rated to carry up to 2,500 lbs. (1,134 kg). Cable, sheaves and finish Equalizing cable is 3/8 in. (10 mm) high-strength multi-strand galvanized steel over deliberately oversized sheaves. Sheave diameter is the quiet one: a cable bent around a small wheel fatigues faster than the same cable bent around a large one, so this is a service-life decision rather than a spec-sheet decision. Columns and beam carry a powder-coat finish; the power system is electric over hydraulic with dual direct-drive cylinders. Perfect For Van and fleet shops where high-roof cargo vans are routine work rather than an occasional surprise. Tall general repair bays wanting one lift for cars, pickups and vans. Truck and upfitter shops that would rather size the beam once than regret it. Collector garages with the ceiling height to take the 181 in. structure. What's in the Box Only what the manufacturer's own feature list states: four triple-telescoping Low-Pro swing arms, double-telescoping screw pads, the padded overhead safety shutoff bar, expandable top beam hardware for either width, the automatic arm restraints, cable and sheave assemblies, and the electric/hydraulic HVLP power unit. Optional 2.5 in. and 5 in. stackable adapters and column-mounted racks are sold separately. Anchors and anything not listed above should not be assumed to be in the crate. Specifications Capacity Value Lifting capacity 10,000 lbs. (4,536 kg) Maximum load per arm 2,500 lbs. (1,134 kg) Arm restraint holding force Over 2000 pounds Bay dimensions are listed in full under “Will It Fit?” above and are not repeated here; rise is in the table under “Confirm the rise before you order”. Reach, power and weight Value Front arm reach 22 in. (559 mm) min to 47.5 in. (1,207 mm) max Rear arm reach 29.5 in. (749 mm) min to 57 in. (1,448 mm) max Motor 220V Noise Less than 70 dB Time to full rise 45 seconds Shipping dimensions 162 in. x 24 in. x 30 in. (4,115 mm x 610 mm x 762 mm) Shipping weight 1,902 lbs. Certification, stated plainly BendPak's own feature list states that this lift is ALI certified: a third party assessed the design against the North American lift safety standard, which is a different and stronger thing than a manufacturer declaring conformity for itself. Insurers, fleet contracts and local inspectors that ask for that listing usually want documentation tied to the model and serial number rather than a line on a web page — ask us and we will get it from the manufacturer before you order. The lift is also covered by a United States patent (Patent No. US11820632B2) and corresponding patents in Canada, China and elsewhere. Shipping and Delivery This lift ships by freight to the lower 48 states as one long crate, listed at 162 in. x 24 in. x 30 in. and 1,902 lbs. You will need a forklift, a dock, or enough hands and equipment to get it off the truck; if you have none of those, take terminal pickup instead and bring suitable equipment. Delivery to a residential address carries a residential fee, quoted live at checkout with the freight. Inspect the crate before you sign. Look for crushed corners, punctures and shifted banding, and write any damage on the bill of lading in front of the driver. A clean signed bill of lading is your statement that the shipment arrived undamaged and is hard to unwind afterwards. Photographs at the tailgate cost nothing and settle claims. Warranty and Service BendPak's full warranty document is linked on this page and governs the terms; our record does not restate a period for this model, so we will not paraphrase one. Two things hold regardless. Do not disassemble a component before you make a claim — a stripped-down part is usually treated as a modified part, and that ends the conversation. And keep the manual with the lift along with the anchor torque record and date of first use; those are what a warranty administrator asks for first. Product Features Durable powder coat finish Expandable top beam accommodates wide or narrow drive-thru configurations Double-telescoping screw pads offer increased versatility Padded overhead safety shutoff bar Exclusive Bi-Metric™ arm design for more versatile arm positioning Single-point safety release Drop-end arms provide a lower pad height Dual hydraulic direct-drive cylinders Electric / hydraulic HVLP power system Self-lubricating dura-glide UHMW polyethylene bearing system Safety locks in each column spaced every 3" Automatic arm restraints withstand over 2000-pounds of side force 3/8"(10mm) High-strength multi-strand galvanized steel equalizing cable Oversized cable sheave diameter reduces cable fatigue Four triple-telescoping arms ALI certified Pick Up and Delivery Our Pick Up locations for Bendpak/Dannmar/Ranger are located in Santa Paula, California & Theodore, Alabama.Call, text, or chat with us if you have questions. 866-774-7743
Checkout happens on the official store. This page mirrors catalog facts in plain HTML for direct reading and crawlability.